Resin Illuminati

Resin Illuminati (https://www.resinilluminati.com/index.php)
-   Action Figures and Accessories (https://www.resinilluminati.com/forumdisplay.php?f=135)
-   -   1:6 Scale Sentinel Command Chair (https://www.resinilluminati.com/showthread.php?t=16622)

AdmiralBuck 07-09-2015 11:11 AM

1:6 Scale Sentinel Command Chair
 
1 Attachment(s)
I recently began a side project to the Sentinel Light Cruiser I am building and that is a 1/6 scale command chair. Using a pdf of full-scale plans supplied by The Cat, I re-sized them and along with an additional 1/10 scale set of plans I found online, I started this scratch build. I also redesigned parts of the chair as it's specific to my late TOS era starship.

http://i791.photobucket.com/albums/y...psti3clkhz.jpg

Paper plans were printed and cut into their individual pieces:

http://i791.photobucket.com/albums/y...psuamteudi.jpg

The cradle and arms were assembled mostly from .060 stock styrene:

http://i791.photobucket.com/albums/y...psyanfbqdz.jpg

The seat portion (not included with the full-size plans, only the 1/10 version had this) is shown here in paper for position only:

http://i791.photobucket.com/albums/y...pstixxv8kb.jpg

The back of the chair was modified with this back support piece. I plan to alter this again to continue the extension to the outer edges of the chair back. The inner seat arms were cut from sheet .125, doubled and glued together to attain the proper width. The hole in the seat bottom is an access panel to the cradle for the wiring of lights to the arms.

http://i791.photobucket.com/albums/y...pstld03pww.jpg
http://i791.photobucket.com/albums/y...psps4nl7tn.jpghttp://i791.photobucket.com/albums/y...psqvfn6n9e.jpghttp://i791.photobucket.com/albums/y...psgultt7l6.jpghttp://i791.photobucket.com/albums/y...psh1y7yopr.jpg

The bottom seat cushion was made from .060 styrene covered in real black leather. The two rear cushions have an additional 1/4" medium density foam rubber pad cut to shape between the back board and wrapped leather cover. The leather was superglued to the back of these styrene back boards, curved to shape, much like upholstering a real chair.

http://i791.photobucket.com/albums/y...pseasanbxs.jpg
http://i791.photobucket.com/albums/y...psk8rhg0ef.jpg

I am not sure if I will cover the inner arms of the seat with leather or just paint the rest of the seat base a semi-gloss black. The arms rests will be painted using the Alclad Black Chrome method.

Next is creating the miniature control panels for each arm.

AdmiralBuck 07-26-2015 03:45 PM

Re: 1:6 Scale Sentinel Command Chair
 
The back support was revised, extending the piece to the chair's outer edges and then beveled. The arm rests were also cut and carved to shape. Sentinel Head Nurse Dixie is seen here modeling the construction phase. (She's also 'borrowed' a uniform from the skipper's cabin)

http://i791.photobucket.com/albums/y...psnizhtyq8.jpg

http://i791.photobucket.com/albums/y...ps2smi8rmi.jpg

http://i791.photobucket.com/albums/y...pstuns3um2.jpg

http://i791.photobucket.com/albums/y...ps6pupsemv.jpg


All times are GMT -7. The time now is 08:35 AM.

Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.